Cannon-instrument miniPV-X Manuel d'utilisateur Page 36
- Page / 130
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
CANNON
®
miniPV-Series Automatic Viscometer with VISCPRO
®
Instruction & Operation Manual
Version 1.a— January, 2011; CANNON
®
Instrument Company
2139 High Tech Road • State College, PA 16803 • USA
30
3. To calibrate temperature, enter the current temperature reading to the
nearest 0.01°C into the Temperature: field, subject to the following:
A decimal point MAY be included as an entry. It should be preceded
by at least two numbers or a "0".
The entered actual temperature must not cause a correction in
temperature greater than +/- 5.0 degrees.
Multiple or successive entries of correction for any temperature are
permissible. A newly entered corrected temperature is mathematically
compensated with the previously entered correction and is stored in
memory by the onboard microprocessor as the latest correction.
Data entry errors
The miniPV Series will not accept temperature reference data outside the
parameters noted previously. If the amount of the correction (delta to
displayed temperature) is too large, the correction will not be accepted.
General/Current Offsets
The General Bath Offset is factory-preset value affecting temperature
control at all temperatures and should not ordinarily be changed. The
Current Offset is the temperature adjustment applied to a particular
temperature to conform bath temperature control to your temperature
reference . Always click the radio button for the Apply As Current
Option when calibrating for a specific temperature.
Training sensors
It is necessary to train instrument sensors in preparation for sample
testing at a specific temperature. The training procedure establishes the
proper power levels for sensor detection of the sample meniscus. The
sensor training data is then stored by the miniPV Series instrument, and
recalled when testing at that temperature. The sensor training procedure
requires approximately 30 minutes (longer at lower temperatures).
NOTE
You will be prompted to train sensors by the instrument hardware or
software whenever a new temperature is selected for miniPV Series
operation. You will be unable to test samples until the training has been
- CONTENTS 1
- CALIBRATING THE miniPV-X 29 2
- OPERATING, MAINTAINING 3
- AND SERVICING THE miniPV-X 73 3
- INDEX 123 5
- INTRODUCTION/INSTALLATION 7
- Measuring Viscosity 8
- Safety cautions 9
- Installation 11
- Installing VISCPRO 12
- software 12
- for Windows 12
- Running the software 13
- Checking configuration 15
- Setting bath temperature 22
- Checking wash functions 23
- Training tube sensors 24
- Calibrating the miniPV Series 24
- TESTING SAMPLES WITH THE 25
- Software selection of blank 28
- Unity Reference blank 29
- Testing volatile samples 29
- Pausing a test 30
- Resuming a test 30
- Aborting a test 31
- Concluding a test 31
- Group configuration 32
- Viewing test results 33
- Creating an analysis 33
- CALIBRATING THE miniPV Series 35
- Training sensors 36
- Standard tube calibration 37
- Calibration procedure 38
- Saving a calibration 40
- USING THE miniPV Series 43
- SOFTWARE 43
- Main Menu 44
- Security options 45
- Initial security setup 45
- Adjusting Security Settings 47
- Analyses Menu 48
- Window Menu 50
- Configure menu 51
- Instrument Settings 53
- Tray Settings: Tube and Bath 55
- Tray Settings: Test 57
- Tray Settings: Wash 59
- Tray Settings: Advanced 61
- Saving a configuration 63
- Calibration 64
- Service menu 66
- Service/Clear Temperature 67
- Train Tube Sensors 69
- Selecting sample actions 70
- The VISCPRO 72
- Saving Sample ID information 74
- Configuring the VI Matcher 75
- Handling errors 77
- Solvent Dispensing System 80
- Emptying the Waste Receiver 81
- Viscometer tubes 82
- Homing the Carousel 83
- Adjusting sample tray height 83
- Adjusting Sample Tray Force 83
- Temperature bath 84
- Draining the bath 85
- Ventilation 86
- Checking bath temperature 86
- Dual-solvent washing 87
- Solvent wash by computer 87
- Preventive maintenance 87
- ?etelpmoC ecnanetniamyliaD 88
- ANALYSIS CONFIGURATION 91
- Sorting analysis data 92
- Using the date filter 93
- Using the sample filter 94
- Resizing table columns 95
- Saving a current analysis 96
- Printing an analysis 96
- Exporting analysis data 97
- CAV DATA TABLE 99
- Date/Sample filters 101
- SAMPLE DATA EXPORT ANALYSIS 105
- Port selection 109
- ERROR DATA EXPORT ANALYSIS 111
- Re-sending export data 116
- ERROR LOG TABLE ANALYSIS 117
- USING THE DATABASE MANAGER 121
- Archiving old data 122
- Importing archived data 123
- REPLACEMENT PARTS LIST 125
- APPENDIX A–MULTIPLE UNIT 127
- CONFIGURATION 127
Produits connexes et manuels pour Instruments de mesure Cannon-instrument miniPV-X
(140 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.050 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels